American Standard AC Not Turning On: Why And How To Fix It?

by HVAC Contributor September 12, 2022, 12:00 pm 1k Views

Perhaps you should turn on your air conditioner once more. What happens, though, if the American Standard AC won’t switch on? What should you do and why does this happen? Don’t be concerned; we can assist! For you, we conducted extensive research.

Understanding the cause of your AC’s failure is crucial. The motor, system, or wiring could all be at fault. The following list will help you identify possible problems with your American Standard AC:

Power Failure.
Defective thermostat.
Overusing the air conditioning.
Low level of refrigerant
Filter is dirty.
Reached the end of life.

Why Won’t The American Standard AC Turn On?

When you try to switch on the AC but it doesn’t work, it might be rather inconvenient. There could be damaged components that require immediate repair or maintenance issues. The causes of your American Standard AC’s malfunction and solutions are listed below. The list is below.

1. Power Failure

An electrical outage is a sudden loss of power that affects appliances and prevents them from turning on. The lack of electricity may be the result of severe weather or a planned power outage by the local government. Another possibility is that the wiring has to be checked.

By looking at the circuit breaker, confirm that the AC unit is wired correctly. The wires should be fastened and tightened at the appropriate terminals. However, aside from the AC unit, make sure the appliances are getting power. If so, it’s possible that the power supply is not the issue. For a more thorough wire analysis, you might ask an electrician for assistance.

2. Defective Thermostat

The thermostat can program modern air conditioning systems. To allow accurate communication between the thermostat and the AC, you might need to reset the thermostat. The following procedures can be used to restart a wireless thermostat made by American Standard:

Even if the AC isn’t working, turn it off. This guards against harm to the AC.
Press “MENU” to access the settings on the thermostat.
Wait for the AC to finish restarting after pressing the “REBOOT” icon and “YES” to confirm the action.

If restarting doesn’t solve the problem, the thermostat may require maintenance or replacement. To fix the thermostat, speak with your HVAC specialist. If not, try one of the alternatives below.

3. Overusing The Air Conditioner

Keep in mind that AC need relaxation. No more than 12 to 16 hours a day should the AC unit be running. When not in use or if the room temperature is just right for you, it is better to leave the AC unit off. Additionally, this lessens the risk of the motors overheating.

The indications that an air conditioner is leaking refrigerant are listed below.

4. Low Level Of Refrigerant

As part of the cooling process for the AC, refrigerant is a liquid chemical that swiftly transforms into a gas. The AC motors will stop operating if the refrigerant level is too low.

There might be a refrigerant leak. Leaking refrigerant wastes energy and could harm the air conditioner. If you don’t solve this problem, you might potentially get hurt.

Finding the leak’s origin is simple with the use of a refrigerant leak detector.

The indications that an air conditioner is leaking refrigerant are listed below.

Slow Cooling Process
The leak will make the compressor work harder to process the refrigerant, which will slow the cooling cycle down. As a result of the condenser fan’s inability to release a cool temperature, the air will start to feel dry. The compressor will eventually quit and lose power as a result of this.

Ice Building Up On Coils
The refrigerant is leaking if ice is accumulating around the evaporator coils. Since refrigerant is initially a liquid, if it doesn’t pass through the coils, it will turn into solid ice, which will obstruct the airflow.

It is a significant problem when an AC develops ice. It is about to melt, which could do permanent harm.

But simply cleaning the evaporator coil, you can fix this. Here are the steps:

Unplug the AC after turning it off.
Remove the top cover by first opening the access panel’s case.
To clean the fan, use a gentle brush. For a smoother action, you can also grease it.
On the coils, mist water and foam cleanser. Give it 10 to 15 minutes to sit.
With a soft cloth, dry the coils, then look for any damage.
Close the lid and start the air conditioning.

But it depends on the kind of refrigerant you previously used in the air conditioner. R-410a is used in American Standard AC units created after 2010. If you previously used R-22, it is best to ask your HVAC specialist whether switching to a different refrigerant is safe for the unit.

Unusual Sound
A low hissing noise is likely coming from the motors in the device, which are vibrating. The motors will collide if the refrigerant line is left empty due to a vibration caused by dry air.

The AC won’t work when it is turned on, but you can hear it hissing as it tries to complete the refrigeration cycle. This is an obvious sign of leakage of refrigerant. You might need to swap out the refrigerant to keep the AC operating.

5. Filter Is Dirty

When air flows through the filter of the air conditioner, dirt is filtered out. Although dirt buildup in the AC filter is typical, you should clean it more frequently to ensure optimal performance. To enhance the quality of the air, think about replacing the worn-out filter.

Therefore, you can follow the guidelines below to replace the AC filter:

Make the new filter ready and certain it is the same size as your air conditioner.
Switch the device off.
The filter can be taken out with a screwdriver. Usually, it is on the AC’s right side.
.To get rid of any leftover dirt, brush the AC.
0Turn on the AC after installing the new filter.

6. Reached The End of Life

The AC has likely reached the end of its useful life if it still won’t switch on. American Standard air conditioners have a 25-year lifespan. As a result, the AC can stop working the same manner that it did when you originally bought it. You might think about purchasing a new unit.

How Much Does A Standard American Air Conditioner Cost?

The cost of an American Standard AC unit, if you’ve opted to get a new one, ranges from roughly $3,500 to $6,100. The details, such as size, model, and installation price, will determine this.

Is A Warranty Provided By American Standard?

A warranty is a written agreement between the seller and the manufacturer. It’s a useful strategy for protecting your AC system from flaws and accidental problems. Not all guarantees, nevertheless, are implied. Some manufacturers will need you to register your product in order to be eligible for their warranty.

American Standard provides a few warranties options. These choices are listed below.

Base Limited Warranty

If there is a manufacturer’s problem, this warranty guarantees that you’ll obtain a replacement item without paying any fees. It also applies to units that are installed within 60 days, whether or not they are registered. Nevertheless, depending on the model and replacement date, you can be responsible for the labor costs.

Limited Registration Warranty

A 10-year guarantee covering manufacturer’s faults is available if you register the device within 60 days of installation. This warranty does not cover the cost of repair labor.

Extended Warranty

You may be eligible for parts and labor coverage for 5 to 12 years, depending on the contract. Even if the equipment is sold to a different owner, this warranty can be transferred. To obtain the best warranty for your product, you can ask the manufacturer.

What Is The SEER Rating For The American Standard?

The seasonal energy efficiency ratio, or SEER, measures how efficiently energy is used in relation to cost of use. The majority of American Standard’s air conditioners have a SEER rating of 14.5 to 22.

Conclusion

We appreciate you reading this far in the article. This taught us many methods for troubleshooting an American Standard air conditioner. Keep in mind that regular maintenance increases the lifespan of the AC.