GE Air Conditioner Beeps But Won’t Turn On: Why And How To Fix It?

When you attempt to switch on your GE air conditioner, it might beep, but the other components might not turn on. We’ve done some research to find out why this happens and what you can do to prevent it because we recognize how annoying this experience may be.

Why Does My GE AC Keep On Beeping?

If your GE air conditioner beeps but won’t turn on, it probably has an issue with the electrical control board. This part of the component controls how its mechanisms and operations are carried out. The control board needs to be repaired by a skilled air conditioner technician.

One Beep: This signifies that the item is getting power and that the power cord is attached. The display panel’s LED lights should turn on, and for a brief while, ’88’ might appear on the screen. When the device restarts during a power outage or when you hit a button on the control panel or remote, you’ll hear this sound.

Two Beeps: If there are two beeps, a control panel or remote control button was pressed but did not function.

Constant Beep: Constant beeping indicates a malfunction with one or more parts, such as the electronic control board, compressor, fan motor, or capacitor. This device’s constant beeping signals a problem that requires fixing.

Typical Causes Of An Air Conditioner That Beeps But Doesn’t Switch On

Control Board Defect: The control board is frequently at blame for this problem. It is in charge of conveying instructions to the air conditioner’s other parts. Even if the unit beeps and briefly illuminates, the fan, compressor, and other components won’t operate if the control board malfunctions. Exposure to moisture, which can damage the microchips and cables, is one potential reason for a control board that isn’t working properly. To avoid this, it’s important to keep the unit’s airflow functioning properly.

Insufficient Power: Verify that the unit is getting enough power before assuming that the control board is broken. Make the following checks:

• Check to see if the switch is on.
• Make sure the device is plugged in.
• Set the thermostat to the preferred setting and temperature.
• Plug in another appliance to check the outlet.
• Press the test and reset button if the power cable contains a circuit interrupter safety feature. In the event of a ground fault, this device is intended to cut off the energy.

Filters That Are Dirty: If an air conditioner’s filters are blocked, it might not turn on. Filters that are too unclean might restrict airflow and cause the compressor to overheat. This issue might be fixed by cleaning or changing the filters.

Troubleshooting Techniques You Can Use

Resetting The Air Conditioner
Resetting the air conditioner can effectively fix internal and minor electrical issues. Restarting the air conditioner can be done in one of two ways:

• Complete power off: Unplug the appliance, turn off the circuit breaker, and leave the appliance off. Plug it back in after waiting five to ten minutes and unplugging it once more.
• Hard reset: Locate a little red reset button on the air conditioner’s bottom edge. Keep pressing the button for five seconds. After a period of time, restart the device.

Inspecting The Power
A low power supply may make it difficult for the air conditioner to switch on. If you have a voltmeter, you can check the voltage to make sure it is between 208 and 240 volts, which is the recommended range.

Searching For Error Codes
If the device beeps and the control panel illuminates, lights up, look for any error warnings on the 88 screen. By comprehending the importance of these codes, you can identify the exact issue. If you require further information on an error code, get in touch with GE’s customer service division.

Confirming The Guarantee
The guarantee can still be valid if your air conditioner is less than a year old. In such cases, GE shall repair the damaged component, together with any related labor charges, without charge.

Resetting The Circuit Breakers
Resetting the circuit breakers in your home is a simple way to fix a breaker that has tripped. Switch the gadget off and then back on without unplugging it.

Cleaning Or Replacing The Filters
For appropriate airflow, the air conditioner’s filters must be cleaned or replaced on a regular basis. As per the manufacturer’s guidelines or once every two weeks, this maintenance routine should be performed.

Time To Call A Professional

If these straightforward troubleshooting techniques fail to resolve the issue, it is advised to contact an air conditioner repair agency. Choose a reputable nearby business with a solid reputation, qualifications, and cooling system repair experience. Before hiring the experts, being aware of what can be wrong with your unit will help you decide whether to repair or replace certain unit components or the entire thing.

Conclusion

Having a competent technician locate and resolve the problem is the best course of action when your GE air conditioner beeps but won’t turn on. Often, the control board is the main culprit, but other components, such as the power supply, dirty filters, or specific error codes, may also be to blame. You may give the experts a clearer explanation of the problem and assure a successful resolution by comprehending the possible reasons and doing straightforward troubleshooting.